DIY CoverLine illuminate KIT for 16mm pcbs (yellow)

(without LED module)

Description

The do-it-yourself (DIY) CoverLine Lightbar KIT combines our high-performance CoverLine aluminum profile with the 50cm aluminum strips with a width of 16mm (available in different versions).

If you have any further questions, we would be happy to help you plan your individual project. Please contact our support for this.

Scope of delivery:

1x LT-3081 CoverLine Aluminium LED Profile 50cm
1x LT-4021 Heat Conductive Pad for 50cm stripe pcbs (16mm)
1x LT-4567 CoverLine V2 acrylic cover 50cm
2x LT-4557 CoverLine V2 end cap flat 3D printing with cable entry yellow
1x LT-4555 CoverLine V2 downholder 3D printing yellow
1x LT-5724 Core conductor rigid 0,5mm² 200cm red
1x LT-5725 Core conductor rigid 0,5mm² 200cm black

There is no LED module included in the scope of delivery. You find the compatible LED modules below.

Compatible LED modules (with socket):

LM281B+

• LT-4890 - 98x LM281B+ LEDs 3500k
• LT-4891 - 98x LM281B+ LEDs 6500k
• LT-5739 - 98x LM281B+ PRO LEDs 3500k

LM301 (B, H, ONE, EVO, MINT)

• LT-4013 - 98x LM301B LEDs 2700k
• LT-4014 - 98x LM301B LEDs 3000k
• LT-4015 - 98x LM301B LEDs 3500k
• LT-4016 - 98x LM301B LEDs 4000k
• LT-4017 - 98x LM301B LEDs 5000k
• LT-4455 - 98x LM301B LEDs 5700k
• LT-4018 - 98x LM301B LEDs 6500k
• LT-4715 - 98x LM301H LEDs 3500k
• LT-4716 - 98x LM301H ONE LEDs 3500k
• LT-4457 - 98x LM301B LEDs 2700k CRI90
• LT-4460 - 98x LM301B LEDs 4000k CRI90
• LT-4520 - 98x LM301H LEDs 3500k CRI90
• LT-5858 - 98x LM301H EVO MINT LEDs
• LT-5832 - 98x LM301H EVO LEDs 3000k
• LT-5833 - 98x LM301H EVO LEDs 4000k
• LT-5834 - 98x LM301H EVO LEDs 3000K+4000k
• LT-5835 - 98x LM301H ONE+EVO 3500K+4000K

Bridgelux F90

• LT-5770 - 98x F90 LEDs 2700k

Bridgelux Thrive

• LT-5761 - 98x Thrive LEDs 2700K
• LT-5416 - 98x Thrive LEDs 3500K
• LT-5555 - 98x Thrive LEDs 4000K
• LT-5556 - 98x Thrive LEDs 5700K

Successful usage of high power LEDs:

Heat management
Applications with high power LEDs need enduring, adequate and plane heat conduction from the first moment of use. It is very important and neccessary to get the heat off the devices to ensure the maximum light output, lifetime and efficiancy.

Drive management
LEDs should be run with a constant current in addition to the manufacturers recommendations. To ensure this we recommend to take constant current power supplies because resistors are always a risk factor in high power LED applications.

IP protection
Unless otherwise stated, the modules are not protected against high humidity or splashing water. If LEDs are used in areas that require increased protection, this must be manufactured according to the requirements.

EMC protection
LEDs are sensitive against heat and electric charge. Please avoid any kind of short circuits or electric discharge to the illuminant. The chip can be damaged or even destroyed.

Storage / JEDEC level
The storage temperature should be from -30°C up to + 80°C in dry ambience. After opening a sealed bag the content should be mounted rapidly. Once absorbed humidity can be removed by tempering the LEDs in some cases. More information can be found in the manufacturers datasheets or on the manufacturer homepages.

Soldering conditions
Each LED has its own soldering conditions that the user should pay attention to. After the launched lead free processing specifications many standarts have changed. Information about recommended soldering can be found in the manufacturers datasheets or on the manufacturer homepages.