LED Leuchten Shop

3. generation now available! 

With RGB and RGBW mode!

New features:
- 3 and 4 channel mode
- alphanumeric display for more info feedback
- new high quality buttons
- optional remote control expands functionality

The MultiLine RGBW Controller is a powerful, cascadable controller with a wide range of features. If you want to know more please read below about ...

the technical data:

- Channels: 3/4
- Status LEDs: 4
- 16.000.000 colors
- PWM: 300Hz (no flickering!)
- Input: 7-30V DC
- PCB power consumption: 50mA
- Uses common anode (plus)
- Dimensions (LxWxH): 110x111x25mm

- Fading effects ex work: 1
- Fading effects with remote: 4
- Fading speed steps ex work: 1
- Fading speeds with remote: 16

- Power supply connection: Clamps
- Illuminants connection: Clamps

- Max. capacitance per channel: 10A
- Max. LED forward voltage: 30V DC
- Max. total capacitance of illuminants: 20A over soldering pads or 16A over clamps

the functional principle:

The latest generation of this controller can be switched from 3 to 4 channel by using an onboard jumper. When running in 3channel RGB mode the controller gets WHITE by mixing R+B+G. If the controller runs in 4channel mode instead it uses the fourth channel to get white. This allows the user to use WARM white LEDs too now! 

The controller can operate 10A (max.) per channel. As the ouput voltage complies with the input voltage (7-30V) it can control a lot of different illuminants. If the project gets larger and more resources are needed the controller can be expanded by further AMPLIFIER circuit boards. Each booster is as powerful as the controller itself.

Because of the 300Hz PWM technology you do not see any kind of flickering when the colors change. That makes the applications possible to be used for wellness or videocams.

If the modul gets disconnected from its energy source the last conditions get reactivatet when reconnected. If the controller was in fading mode it goes on fading and if it showed a (mixed) color it goes on with that. This is very useful for all applications that shall run without human administration.

the buttons:

The controller has different onboard buttons for manual control:

1) Alphanumeric display: This gives you visual feedback on controller status, button press, remote signals and running programs.

2) Two intensity buttons per channel (Up/Down)

The status LEDs are already diffused in the color tey control. One push changes the intesity up or down.

New: Id the controller is used in RGB mode a press on the white channels buttons will lower/increase R, G and B channel untill 100% so that white appears as mixed color. Of course you can also use the R, G and B buttons to reach white but this lasts longer.

3a) Starting a program (without remote control)

The ex-work fading program kann be startet (and stopped) by pressing the PAUSE button.

3b) Starting a program (with remote control)

If you have the optional remote control you have access to all four fading/blinking effects. You can start/change them by using the four grey button on the roght of the remote control. You can also control the speed (16 steps) by using the two white button on the top of the remote.

4) Pause button

This button stop and continous the current fading effect.

the remote controlling / upgrading:

The MultiLine controller uses the same IR remote control (LT-600/1002) like all other LED-TECH RGB/W components. If you already have such a remote you do not have to buy it especially. A detailled description of all buttons of the remote can be found in the remote part description.

With the optional remote you upgrade the MultiLine controller for only 10,- Euros to a professional controller thats range of features can mess with competitive products that are 3-4 timmes more expensive. But the controller does not only get the possibility of wireless communication it also gets the features

- 1 more fading effect
- 2 more flashing effects
- wireless On / Off switching
- direct choise of different colors
- Dimmable single colors
- Speedadjustment of fading/flashing effects

(Above linked video shows some sample adjustments)

The onboard infrared sensor is mounted in a way that it is able to receive signals even in the below mentioned MultiLine IP65 housing. The transparent cap ensures that hte signals can be received by the IR sensor. If you want to mount the controller invisibly you can use the external MultiLine IR sensor LT-1003 with integrated anti-jamming technic.

The onboard pics show and explain the two different jumper settings. We intendingly designed the jumper settings in a way that the jumper has to be set anyway because these little things often like to get lost as every PC friend may confirm ...

the flexibility (amplifier):

The MultiLine RGB/W controller can be extended by any number of amplifers so the application gets cascadeable. A simple, money saving and efficiant possibility to built (realy) big applications and control them centrally. The PWM signal is transported by wire (LT-1016) by using the central 10 pole socket on the controller. This socket is also on each amplifier PCBs twice. The first one to receive the signal, the second one to transport it to other possible amplifier PCBs.

The amplifier can be ordered here.

useful supply / help:

Dedicated MultiLine IP65 housing made from plastic with transparent sealed cap (120x120x55mm)

the individuality (project service):

If you are interested in special onboard printings (reseller versions), different speed times or other modifications please do not hesitate to contact our support to tell us your special wishes.