|from 1||83,95 €||99,90 €|
|Chemical Compatibility||723.42 KB|
|Product data sheet||210.21 KB|
LED-TECH.DE 308 XT High-Performance KIT (4000k)
The Samsung LM301B is currently one of the most efficient LEDs on the market and exceeds the 200lm/W limit.
The LED-TECH.DE 308 PCBs offer you completely new possibilities to realize demanding applications. Through the sockets you can easily extend your application almost infinitely.
Easy feeding without soldering! The insulated conductor is simply inserted into the clamping point as far as it will go and automatically fixed securely. Please use solid and stripped wires.
This KIT includes:
The advantages at a glance:
- easy installation
- high luminous flux
- individually stackable
- based on constant current
- 308x Samsung LEDs per board
- very good price / performance ratio
- fast and easy handling through plug-in system
- optimized surface illumination, e.g. grow, advertising space
- solderless PCB with sockets for rigid strands (0.2 - 0.75 mm²).
In our test, we achieved the following values at an ambient temperature of ~ 20 ° C:
The LED-TECH.DE 308 was supplied with 3.5A without heat sink (~ 140W) and warmed up to approx. 58.8 ° C
- ATTENTION! For use with constant CURRENT only!
*We distinguish the modules between CC and CV modules. Please note the product subtitle.
|0.350 A||36.72 V||12.85 W|
|0.700 A||37.32 V||26.12 W|
|1.050 A||37.77 V||39.66 W|
|1.400 A||38.15 V||53.41 W|
|1.750 A||38.49 V||67.36 W|
|2.100 A||38.81 V||81.50 W|
|2.800 A||39.38 V||110.26 W|
|3.500 A||39.90 V||139.65 W|
|0.350 A||2949 lm||229.49 lm/W|
|0.700 A||5842 lm||223.66 lm/W|
|1.050 A||8670 lm||218.61 lm/W|
|1.400 A||11442 lm||214.23 lm/W|
|1.750 A||14148 lm||210.04 lm/W|
|2.100 A||16827 lm||206.47 lm/W|
|2.800 A||22041 lm||199.90 lm/W|
|3.500 A||27110 lm||194.13 lm/W|
The values shown in the table are averages of the 4000K modules.
For the boards we can recommend the following power supplies:
|Boards parallel||Power supply (dimable)|
The board offered here is 100% compatible with our SYSTEM250 construction kit. Our support will gladly assist you in the planning/design of your personal SYSTEM250 application. The gallery shows a sample composition.
Successful usage of high power LEDs:
Applications with high power LEDs need enduring, adequate and plane heat conduction from the first moment of use. It is very important and neccessary to get the heat off the devices to ensure the maximum light output, lifetime and efficiancy.
LEDs should be run with a constant current in addition to the manufacturers recommendations. To ensure this we recommend to take constant current power supplies because resistors are always a risk factor in high power LED applications.
Unless otherwise stated, the modules are not protected against high humidity or splashing water. If LEDs are used in areas that require increased protection, this must be manufactured according to the requirements.
LEDs are sensitive against heat and electric charge. Please avoid any kind of short circuits or electric discharge to the illuminant. The chip can be damaged or even destroyed.
Storage / JEDEC level
The storage temperature should be from -30°C up to + 80°C in dry ambience. After opening a sealed bag the content should be mounted rapidly. Once absorbed humidity can be removed by tempering the LEDs in some cases. More information can be found in the manufacturers datasheets or on the manufacturer homepages.
Each LED has its own soldering conditions that the user should pay attention to. After the launched lead free processing specifications many standarts have changed. Information about recommended soldering can be found in the manufacturers datasheets or on the manufacturer homepages.